ASTM A335 P91 Alloy Steel 90 Degree LR Pipe Fittings

ASTM A335 P91 Alloy Steel 90 Degree LR Pipe Fittings
Product Introduction:
Tianjin Baode Steel makes ASTM A335 P91 alloy steel 90 degree long radius (LR) elbows with a 1.5D centerline radius. Outside diameter runs from 1/2" to 48" (DN15–DN1200) and wall thickness from 2mm to 60mm. Angles cover 15, 30, 45, 60, 90, 135 and 180 degree, plus special degrees. P91 is a 9Cr-1Mo-V creep-strength-enhanced steel for high-temperature, high-pressure service. In steam lines where P11 and P22 need heavier walls, a P91 elbow lets the designer cut weight and weld volume. The same factory also supplies grades from P1 to P921, so mixed Cr-Mo orders can ship together. We form each order by hot pushing, stamping or welding, depending on batch size and wall thickness. Surface options include sand blasting, painting, hot dipped galvanizing, 3LPE and FBE coating. MOQ is 1 piece. Standard lead time is 15 days outside peak season and 30 days in peak season. Send your grade, size and wall thickness for a quote.
Send Inquiry
Description
Technical Parameters

ASTM A335 P91 Alloy Steel 90 Degree LR Pipe Fittings

Built for steam lines that run hot, year after year.

1.5D long radius A gentler turn, so lower pressure drop at every bend.
P91 creep-resistant steel Designers can often cut wall thickness against P11 and P22.
DN15 to DN1200, wall 2mm to 60mm Main line, branches and tie-ins from one supplier.
Hot pushing, stamping or welding We quote on the process that fits your batch and wall.

ASTM A335 P91 Alloy Steel 90 Degree LR Pipe Fittings

ASTM A335 P91 Elbow Technical Specifications

Material & Standards Size & Geometry Procurement
Standard: ASTM A335
Steel Grade: P1,P2,P5,P9,P11,P12,P15,P21,P22,P23,P24,P36,P91,P92,P93,P115,P122,P911,P921
Surface: Sand Blasting,Painting,Hot Dipped Galvanized,3LPE Coating,FBE Coating etc
Radius: Long Radius (1.5D)
Degree: 15 degree,30 degree,45 degree,60 degree,90 degree,135 degree,180 degree and other special degree
Out Diameter: 1/2"-48"(DN15-DN1200)
Wall Thickness: 2mm-60mm
MOQ: 1 piece
Standard Lead Time: 15 days, excluding peak season
Peak Season Lead Time: 30 days
Warranty: 1 year

Why Specify P91 Long Radius Elbows

1.5D Long Radius Geometry

The 1.5D centerline radius turns the flow more gently than a 1D short radius elbow. Pressure drop at each bend is lower, and the load on the outer wall is spread over a longer arc.

On a steam run with several direction changes, that means less pressure lost between boiler and turbine.

P91 Creep-Resistant Chemistry

P91 adds vanadium and niobium to a 9% chromium, 1% molybdenum base. That raises allowable stress at high temperature, so designers can often specify thinner walls than P11 or P22 for the same steam conditions.

Thinner walls mean less weld metal and lighter supports. Final wall thickness still follows your design code and calculation.

Three Forming Routes

Hot pushing suits mass production. Stamping suits small batches and special specifications. Welding covers complex pipeline connections.

We pick the route from your quantity, wall thickness and delivery date, so a 1-piece repair order and a project lot are both quoted on the right process.

One Source for the Whole Line

From 1/2" to 48" (DN15–DN1200), wall 2mm–60mm, angles from 15 to 180 degree plus special degrees.

Main line, branches and tie-ins can come on one purchase order, finished with sand blasting, painting, galvanizing, 3LPE or FBE coating.

ASTM A335 P91 long radius elbow

ASTM A335 P91 Elbow Production Process

The production process of ASTM A335 P91 Alloy Steel 90 Degree LR Pipe Fittings primarily includes hot pushing, stamping, and welding techniques, with specific procedures varying depending on the process:

1 2 3

1: Hot pressing forming

Cutting and Heating:Place the alloy tube blank into the mold and soften it through induction heating or flame heating.
Push molding:Under the push of the push molding machine, the tube blank moves forward along the mold, expands and bends due to heat, and the core mold controls the internal arc compression metal flow to maintain uniform wall thickness.
Shaping and processing:Adjust the shape through molds and strengthen the surface with shot blasting treatment.

2: Stamping forming

Mold positioning:Place the tube blank into the lower mold, add the inner core and end mold to fix the position.
Extrusion molding:The upper mold moves down to extrude the metal, and an elbow is formed under the constraint of the outer mold. The thickness of the outer arc wall is reduced by about 10% due to stretching.
Demoulding inspection:Dimensional inspection after stamping, suitable for the production of small batches and thick walled elbows.
Heat treatment:Heat treatment according to standards

3: welding process

Cutting and assembly:Cut pipes or steel plates according to the design, weld and splice them into elbow prototypes.
Testing and processing:Perform non-destructive testing after welding is completed, and process grooves or adjust dimensions as required.
alloy steel elbow produce
alloy steel pipe fittings inspection
ASTM A234 WP91 Elbow

Different processes are suitable for specific scenarios: hot pressing is suitable for mass production of carbon steel/alloy steel elbows, stamping is suitable for small batches or special specifications, and welding is flexible to meet complex pipeline connection requirements.

Where P91 Long Radius Elbows Are Used

Power Plant Steam Lines

The problem:Main steam and hot reheat lines run hot for decades, and heavy P22 walls add weight and weld volume.
What we supply:P91 elbows at 1.5D, so the designer can cut wall thickness without tightening the bend.
Result:Lighter pipe runs and less weld metal at every joint.

Refinery and Petrochemical Piping

The problem:High-temperature Cr-Mo lines often mix several grades, and splitting them across suppliers slows the project.
What we supply:Grades from P1 to P921 on one order, in sizes from DN15 to DN1200.
Result:One supplier and one inspection route for the whole Cr-Mo package.

HRSG and Boiler Connecting Pipe

The problem:Start-ups and shutdowns put repeated thermal cycles on every bend.
What we supply:Long radius bends in P91, with the load spread over a longer arc than a short radius elbow.
Result:More margin at the bend on lines that cycle often.

Thick-Wall Pressure Piping

The problem:Wall thickness up to 60mm is hard to form by hot pushing in small quantities.
What we supply:Stamping route for small batches and thick walled elbows.
Result:Thick-wall orders accepted from a single piece, with no batch minimum to fill.

OEM/ODM Service for P91 Elbows

Send Your Requirement

Send grade, DN, wall thickness and angle. Drawings are welcome. For special degrees outside the standard 15 to 180 degree range, a sketch with the centerline radius is enough to start.

Choose the Process Route

We review quantity and wall thickness, then pick hot pushing, stamping or welding. Mass production, small batches and complex connections each go to the route that fits.

Produce, Heat Treat and Finish

Forming comes first, then heat treatment according to the standard, then surface work: sand blasting, painting, hot dipped galvanizing, 3LPE or FBE coating.

Inspect, Pack and Ship

Dimensional inspection runs after forming, and non-destructive testing follows welding on welded routes. Small items go into wooden cases, large items onto wooden pallets.

Factory Strength and Certificates

Tianjin Baode Steel factory
Tianjin Baode Steel production workshop
Tianjin Baode Steel pipe fittings workshop

Pipe fittings shipped to 40+ countries and regions

Tianjin Baode Steel exports to North America, South America, Southeast Asia, the Middle East and Africa. The same factory builds the P91 elbows on this page, and you can read more on the company introduction page or see the production equipment.

500+Employees
400+Production lines
40+Countries and regions served

Management systems are registered to ISO 9001:2015, ISO 14001:2015 and ISO 45001:2018, and Baode is an AAA-rated credit enterprise. Certificate details are on the certificate page.

Quality Control for P91 Elbows

01

Forming Control

Outer arc wall thickness is the critical dimension on an elbow. A stamped bend thins by about 10% on the outer arc, so the finished wall is checked against your minimum wall before the part moves on.

02

Heat Treatment

Heat treatment follows the standard for the grade. P91 reaches its creep strength only through correct normalizing and tempering, so this step is never shortened to save time.

03

Dimensional Inspection

After forming, angle, centerline radius, outside diameter and wall thickness are measured against the order.

04

Non-Destructive Testing

Welded elbows go through non-destructive testing after welding. Grooves are then machined or dimensions adjusted as required. Our test instruments are listed on the test equipment page.

Client Cases

Main Steam Line Upgrade, Thermal Power Plant

Client:S****** Power Co., Ltd.
Region:Southeast Asia
Challenge:Heavy P22 elbows were adding weight and weld volume to a main steam retrofit.
Solution:ASTM A335 P91 90 degree LR (1.5D) elbows, DN3**, wall 4* mm, hot pushed.
Delivery:2** pieces, packed in wooden cases, 1 x 20GP, standard 15-day lead time.
Outcome:Elbows passed dimensional inspection and were released for site welding.
ASTM A234 WP91 Elbow

alloy steel pipe fittings packing

Packing, Loading and Warranty

Packing

Small items go into wooden cases. Large items are loaded on wooden pallets.

Container Loading

20GP: about 20 standard wooden cases, roughly 18–22 tons.

40HQ: about 40 standard wooden cases, roughly 26–28 tons.

1-Year Warranty

The warranty runs for 1 year. Damage from improper operation or improper installation is not covered.

ASTM A335 P91 Elbow FAQ

What is the MOQ for ASTM A335 P91 90 degree LR elbows?+

The MOQ is 1 piece. Repair and replacement orders are accepted at the same price logic as project lots.

What is the lead time for P91 long radius elbows?+

Standard lead time is 15 days, excluding peak season. In peak season it is 30 days.

What size and wall thickness range can you supply?+

Outside diameter runs from 1/2" to 48" (DN15–DN1200) and wall thickness from 2mm to 60mm. Angles run from 15 to 180 degree, plus special degrees on request.

What is the difference between long radius and short radius elbows?+

A long radius (LR) elbow has a centerline radius of 1.5D. A short radius elbow uses 1D. The LR bend gives a lower pressure drop and spreads load over a longer arc, so it is the usual choice for steam lines.

Which forming process do you use for P91 elbows?+

Hot pushing is used for mass production, stamping for small batches, thick walls and special specifications, and welding for complex pipeline connections.

Send your grade, size and wall thickness for a P91 elbow quote.

Request a Quote

 

Hot Tags: ASTM A335 P91 elbow, P91 90 degree elbow, alloy steel 90 degree LR elbow, long radius elbow 1.5D, P91 alloy steel pipe fittings, A335 P91 pipe fittings manufacturer, P91 elbow supplier China, alloy steel elbow, Sheet Metal 90 Degree Elbow

Send Inquiry
you dream it, we design it
We will find it for you as soon as possible
The product you need
contact us