Complete Analysis Of 12 Commonly Used Flange Types

Aug 06, 2025

Leave a message

Flanges, as core connectors in piping systems, pressure vessels, and industrial equipment, fulfill critical functions such as sealing, pressure bearing, and convenient assembly and disassembly. According to statistics, 35% of industrial pipeline failures are due to improper flange selection or installation. Choosing the right flange type can extend system life by 2-3 times. I've compiled the structural characteristics, standards, and application scenarios of 12 common flanges. Please contact us if you have any questions.


1. Slip-on Flange (PL)-The "Standard" for Economical Connections
Structural Features: The flange and pipe are directly connected via a fillet weld, without a transition neck.
Technical Parameters:
• Pressure Rating: PN0.6-PN40 (American Standard Class 150-Class 300)
• Operating Temperature: -20°C to +350°C (Carbon Steel)
• Sealing Surface: Full Face (FF) / Raised Face (RF)
Core Advantages:
• Low Cost (40% lower than Neck Weld Flanges)
• Easy Installation (Single-Sided Welding)
Typical Applications:
• Water Treatment Systems (DN50-DN300 Low-Pressure Pipes)
• Air Conditioning Circulating Water Pipes (Non-Corrosive Media)
Case Study: A chemical plant's circulating water system switched to PN16 flat-bed flanges, shortening construction time by 30% and reducing initial investment by 18%.


2. Neck Weld Flange (WN) - The "Rigid Guardian" for High-Pressure Applications
Structural Features: Flange with a long neck transition, with the neck connected to the pipe by butt welding. Technical Parameters:
• Pressure Rating: PN10-PN250 (American Standard Class 150-Class 2500)
• Operating Temperature: -196°C to +550°C (304 stainless steel)
• Sealing Surfaces: Raised Face (RF) / Concave-convex Face (MFM) / Tongue-and-Groove Face (TG)
Core Advantages:
• Strong pressure-bearing capacity (stress distribution design at the neck)
• Excellent fatigue resistance (high weld joint strength)
Typical Applications:
• Steam pipelines (DN100 and above, high-pressure systems)
• Petroleum refining units (high-temperature, high-pressure operating conditions)
Innovative Application: An LNG receiving terminal uses -196°C low-temperature butt-weld flanges to safely transport ultra-low-temperature media.

 

3. Loose-Sleeve Flange (LF) - The "Adaptation Expert" for Non-Metallic Pipes
Structural Features: The flange and pipe are connected via flanging or clamping rings, not direct welding.
Technical Parameters:
• Pressure Rating: PN0.6-PN2.5 (low-pressure scenarios)
• Applicable Pipes: Non-metallic Materials such as Plastic, Fiberglass, and Rubber
• Sealing Method: Rubber Gasket/PTFE-Coated Gasket
Core Advantages:
• Avoids damage to non-metallic pipes caused by metal welding
• Rotatable flange facilitates centering installation
Typical Applications:
• Chemical Acid and Alkali Pipelines (PVC/PP Pipes)
• Semiconductor Ultrapure Water Systems (PVDF Pipes)
Case Study: An electronics factory's ultrapure water system used a loose-sleeve flange to connect PVDF pipes, reducing leakage rates from 5% to 0.1%.


4. Threaded Flange (TH) - A "Quick Connector" for Small Diameters and High Pressures
Structural Features: The flange has a tapered pipe thread on the inner hole, which screws into the pipe's outer thread.
Technical Parameters:
• Pressure Rating: PN2.5-PN40 (American Standard Class 150-Class 300)
• Applicable Pipe Diameter: DN6-DN100 (1/8"-4")
• Sealing Method: PTFE Tape/Sealant
Key Advantages:
• Quick Installation (No Welding Required)
• Suitable for Buried Pipes (Removable for Maintenance)
Typical Applications:
• Fire Water Systems (Galvanized Steel Pipe Connections)
• Instrument Air Pipes (Small Diameter Stainless Steel Pipes)
Selection Key: Verify that the thread specification (e.g., NPT/BSPT) matches the pipe.


5. Socket Weld Flange (SW) - A Stable Connection for Small Diameters and High Temperatures
Structural Features: The flange has a socket-shaped inner hole, and the pipe is connected by fillet welds after insertion.
Technical Parameters:
• Pressure Rating: PN10-PN40 (American Standard Class 300-Class 600)
• Applicable Pipe Diameter: DN10-DN80 (1/2"-3")
• Applicable Temperature: -30°C to +425°C (Alloy Steel)
Core Advantages:
• High welding strength (socket-and-spigot joint reduces stress concentration)
• Suitable for high-temperature, high-pressure, and small-diameter applications
Typical Applications:
• Boiler feedwater lines (high-temperature steam below DN50)
• Chemical heat exchanger connections (small-diameter process piping)
Comparative Advantages: 2x the pressure-bearing capacity of threaded flanges and superior vibration resistance compared to flat-weld flanges.


6. Long Neck Weld Neck Flange (WNX) - A "Stress Distributor" for Ultra-Low-Temperature Conditions
Structural Features: Neck length 1.5-2 times that of a standard weld neck flange, with a tapered transition section. Technical Parameters:
• Pressure Rating: PN10-PN100 (American Standard Class 300-Class 900)
• Operating Temperature: -196°C to +200°C (cryogenic steel)
• Neck Length: Typically 1-1.5 times the pipe diameter
Core Advantages:
• Reduces stress concentration in cryogenic environments
• Reduces the risk of fatigue cracking
Typical Applications:
• LNG tank outlet piping (-162°C operating temperature)
• Liquid oxygen/liquid nitrogen piping in air separation plants
Case Study: At an air separation unit, the use of long-neck butt-weld flanges reduced the leakage rate of cryogenic pipelines by 80%.

 

7. Integrally Forged Flange (IF) - The "Strength" of High-Pressure Vessels
Structural Features: The flange and the shell are integrally forged, with no welded joints.
Technical Parameters:
• Pressure Rating: PN100-PN630 (American Standard Class 900-Class 4500)
• Applications: Nuclear power/petrochemical high-pressure vessels
• Manufacturing Standard: ASME BPVC Section VIII Div. 1
Core Advantages:
• Eliminates the risk of weld defects
• Pressure capacity 2-3 times that of ordinary flanges
Typical Applications:
• Nuclear reactor pressure vessel interfaces
• High-pressure polyethylene reactors
Selection Key: An UT (Ultrasonic Testing) report is required to ensure forging quality.


8. American Standard ASME Flange - The "Common Standard" for the North American Market
Classification System:
• Class 150/300/600/900/1500/2500 (Pressure Rating)
• Weld Neck Flange (WN)/Slip-On Flange (SW)/Threaded Flange (TH)
Sealing Surface Types:
• RF (Raised Face) / MFM (Mutual Face) / TG (Tongue and Groove Face)
Typical Applications:
• North American oil and gas pipelines
• Global supply chain equipment for multinational corporations
Case study: A multinational chemical project standardized on ASME B16.5 flanges, achieving seamless integration of equipment from China, the US, and Europe.


9. European Standard EN Flanges - The "Precision Specification" for the European Market
Classification System:
• PN6/PN10/PN16/PN25/PN40 (Pressure Rating)
• Flat Flange (PL) / Weld Neck Flange (WN) / Loose Flange (LF)
Sealing Surface Types:
• Full Face (FF) / Raised Face (RF) / MFM (Mutual Face)
Typical Applications:
• Water treatment systems in EU countries
• German industrial equipment export projects
Comparative Differences: Compared to American standard flanges, European standard flanges are thinner but have closer bolt spacing.

 

10. Tank Flange (API 6A) - "Sealing Expert" for Oil and Gas Storage and Transportation
Structural Features:
• Complies with API 6A standards, with self-tightening sealing rings
• Suitable for manholes/scavenging ports in high-pressure tanks
Technical Parameters:
• Pressure rating: 2000 psi/5000 psi/10000 psi
• Temperature range: -60°C to +204°C
• Sealing material: Nitrile rubber/Fluoro rubber
Typical Applications:
• Offshore platform crude oil storage tanks
• Liquefied natural gas receiving terminals
Innovative design: Dual sealing ring structure, leak rate less than 1×10⁻⁶Pa·m³/s.


11. Sanitary Flange (DIN 11851) - "Clean Connection" for Food and Pharmaceutical Applications
Structural Features:
• Clamp-type quick-connect, no-dead-spot design
• Surface roughness Ra ≤ 0.8μm
Technical Parameters:
• Pressure rating: PN10 (normal temperature operating conditions)
• Material: 316L stainless steel
• Sealing method: Silicone rubber O-ring
Typical applications:
• Dairy production lines (CIP cleaning systems)
• Biopharmaceutical fermentation tanks
Case study: A vaccine manufacturer reduced its FDA certification time by 40% after adopting sanitary flanges.

 

12. Reducing Flange (RF/BL) - A "Space Adapter" for Reducing Connections
Structural Features:
• One end has a large diameter, the other has a small diameter, achieving pipe diameter transitions
• Available as concentric reducers or eccentric reducers
Technical Parameters:
• Pressure rating: PN1.0-PN16 (determined by the larger diameter end)
• Reduction ratio: Typically ≤ 2:1 (to avoid fluid impact)
Typical Applications:
• Boiler economizer inlet and outlet (DN300 → DN200)
• Chemical reactor inlet and outlet reduction
Design Key Points: Eccentric reducing flanges must be marked with the eccentricity direction (e.g., "TOP UP" indicates top alignment).

 

Core Principles of Flange Selection and Installation
1. Pressure-Temperature Matching Principle:
• For high-temperature operating conditions (>350°C), alloy steel (e.g., F304/F316L) is required.
• For low-temperature operating conditions (<-20°C), a low-temperature impact test (e.g., ASTM A350 LF2) is required.
2. Media Compatibility Principle:
• Hastelloy/titanium flanges should be used for highly corrosive media (such as concentrated sulfuric acid).
• 304 stainless steel is not suitable for environments containing chloride ions (due to pitting corrosion).
3. Sealing Surface Matching Principles:
• Raised-face (RF) flanges require a spiral wound gasket.
• Tongue-and-groove (TG) flanges require an octagonal metal ring gasket.
4. Key Points for Installation Specifications:
• Tighten bolts symmetrically (gradually tighten to the specified torque in three steps).
• Low-temperature flanges require liquid nitrogen freezing during installation (to eliminate shrinkage gaps).

Send Inquiry
you dream it, we design it
We will find it for you as soon as possible
The product you need
contact us